2
$\begingroup$

As the title states, I am trying to find a way to measure the dipole moment(m) for my magnetorquer.

I am planning to use magnetorquers for desaturating my reaction wheels for a project. I understand that there is a relation m=nIA where m is the dipole moment, I is the current, n is the no. of turns and A is the cross sectional area of the torque rod. I intend to use that formula to calculate how much voltage to apply to my magnetorquer.

But I would also like to check that I am actually getting the correct dipole moment physically. Are there any ways to experimentally measure the dipole moment strength of my magnetorquer?

I have done some research and came across this formula on this wikipedia page:

enter image description here

https://en.wikipedia.org/wiki/Magnetic_moment

My plan is to use a magnetometer to measure the magnetic field strength at a distance r ( This would then be |r| ) away from the magnetorquer, and assume that the position vector and magnetic moment vector are parallel to simply the dot product of m and r.

Would this work?

Thanks

$\endgroup$
  • 4
    $\begingroup$ This question might find a better home on the Physics Stack Exchange. Also, try looking at this answer: space.stackexchange.com/questions/2239/… $\endgroup$ – Phiteros Oct 8 '16 at 18:50
  • $\begingroup$ The three close votes say this is a duplicate - if there is actually a good answer to the specific question "Ways to measure dipole moment of magnetorquer" please post a link to that answer. I've posted an answer mentioning two ways to measure the dipole moment of a magnetotorquer (via magnetometer and sense coil) but I'd be happy to see that there is better answer - someone please post a link to this answer - thanks! $\endgroup$ – uhoh Oct 9 '16 at 0:28
  • $\begingroup$ @uhoh I agree that it is on-topic. However, I think that the Physics SE could provide a faster, better answer about how to calculate and measure dipole moments as this is, ultimately, physics. $\endgroup$ – Phiteros Oct 9 '16 at 0:45
  • $\begingroup$ @Phiteros Physics SE frequently closes questions because they are "engineering, and not physics". This is not a question about physics. All orbital mechanics questions here (there are many) use physics, but they are not about physics as actually defined by the physics stackexchange "community". Rocket engines use physics too. Someday I hope there will be a new Applied Physics Stackexchange (or Applied and Engineering Phys.) and that would be a great place for this question. This is a piece of standard satellite equipment and the question is how to test the equipment's function. $\endgroup$ – uhoh Oct 9 '16 at 0:57
  • 2
    $\begingroup$ @uhoh That's a pretty stupid policy of theirs. There is an Engineering SE, but it's in beta. $\endgroup$ – Phiteros Oct 9 '16 at 1:20
2
$\begingroup$

Understanding how to test and qualify systems of a satellite prototype is certainly on-topic in Space Exploration Stackexchange. Cubesat development is always conceptual at first, and you definitely need to use some physics to develop your understanding. That doesn't mean the question should be moved to Physics Stackexchange.

Measure in the plane perpendicular to the $\mathbb{m}$ direction and centered on the center of the device so that the $\mathbf{m \cdot r} $ term is zero. Then point the sensing direction of the magnetometer parallel to the $ \mathbb{m}$ direction. Now you have a scalar equation:

$$B = \mu H = \frac{4\pi \times 10^{-7}}{4\pi} \frac{m}{r^3} $$

$$B = \mu H = 10^{-7} \frac{m}{r^3} $$

$$m = 10^{7} B r^3 $$

So move the magnetometer close enough so that you are getting a good signal, then plug in the distance as $r$ and the measured $B$ and you have an approximate measurement of $m$.

A second way to do this is to drive your magnetotorquer with a low frequency sine wave and use a second small "sense coil" to measure the EMF at a distance. This can often be more accurate than a magnetometer, but it is tricky to do correctly.

Also remember that the magnetotorquer has a permeable material - the core that the coil is wrapped around that is long and skinny) and that's not necessarily going to be linear, so you should make a series of measurements at different currents. You should also make sure that $r$ is somewhat larger than the length of the rod, or measure at a few different distances. The magnetotorquer is not at all a perfect point dipole.

Also make sure there are no other ferromagnetic materials nearby.

In order to deal with the Earth's magnetic field, you can just turn the current on and off and look at the change in B.

The problem is at low fields, low cost magnetometers are not very accurate, so if you want to use an "Arduino class chip" (hobby type) or one in your phone, you may get results that are a bit off. But it could be a good sanity check or starting point at least.

This is actually not an easy measurement to do correctly. But you can get experiment with it even using an "unofficial magnetotorquer" to get a feeling for the process.

$\endgroup$

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.