10
$\begingroup$

Figure 1 of this article about craters and collapse features on Mars with high depth/diameter ratios shows that ratios higher than 0.2 are exceptional.

This presentation of the Program of the Second MSL Landing Site Workshop about possible landing sites in Sinus Meridiani shows an image of a "crater" that is 2.4 km wide and 750 meters deep ! (But judging from the elevation chart of Mars Trek the crater is only about 100 m deep.)

Collapse feature

Because the ratio of this feature is more than 0.3 and it has no clear rim, it is very likely that this is not an impact crater at all.

Unusually deep fresh craters were recorded in SW Utopia and Isidis Planitia in this article.

Are there more known features on Mars with such a very high depth/diameter ratio ?

$\endgroup$
12
  • $\begingroup$ Does this feature in the image have a name? $\endgroup$
    – BlueCoder
    Sep 12, 2018 at 11:44
  • $\begingroup$ @BlueCoder Could not find a name at planetarynames.wr.usgs.gov/nomenclature/AdvancedSearch so i think you could propose a name. $\endgroup$
    – Cornelis
    Sep 12, 2018 at 13:14
  • 1
    $\begingroup$ The concept of a depth to diameter ratio is an interesting idea. I'm still trying to get my head around it. In a way it's an analogous of the average/overall slope angle of the wall of the "crater". This angle will largely be dictated by the properties of the wall rock (ie, by way of example, loose sand will have a shallow angle, very competent basalt will have a high angle). Generally this angle will be the angle of rest for the rock type. The other things that will affect the depth of an impact crater will be the hardness & competency of of the host rock. $\endgroup$
    – Fred
    Sep 12, 2018 at 17:17
  • 1
    $\begingroup$ Taking some rough measurements from the screen. I get a diameter of 110 mm & a wall width of 30 mm (on the rightmost side). With a depth to diameter ratio of 0.3 the depth is 33 mm (0.3 x 110). Get the arc tan of (33/30) gives a wall angle of 47 degrees. $\endgroup$
    – Fred
    Sep 12, 2018 at 17:20
  • 1
    $\begingroup$ You might find this interesting. A new global database of Mars impact craters≥1 km:2. Global crater properties and regional variationsof the simple-to-complex transition diameter. From Fig 11, the higher d/D ratio craters seem to lie between latitudes -30 & +30. $\endgroup$
    – Fred
    Jul 7, 2022 at 0:32

2 Answers 2

5
$\begingroup$

The d/D ratio of Martian craters vary from 0.1 to 0.4 with mean value of 0.23. The largest crater with diameter 33m has d/D ratio of 0.2 but smaller craters have higher d/D value. One crater has a surprisingly high d/D value: 0.5. A plot of d/D ratio vs diameter is drawn showing the variation in the values:

enter image description here

Shallower craters have d/D values of less than 0.3

enter image description here

a: 0.50 ; b: 0.42 ; c: 0.39 ; d: 0.42

The variation in this value depends on target material properties like varying strength, porosity, or layering of targets; or impactor conditions such as impact velocity, impact angle, or physical state of the bolide (i.e., strength, fractured versus cohesive). The dependencies are listed below:

  1. Spallation can be seen in targets with porosity up to 60%. The ratio of spall diameter to pit diameter is not strongly dependent on porosity and is between 1.5 and 3. The range of the ratio is similar to those found for microcraters on lunar rocks and glass targets in the laboratory.
  2. The depth of a crater cavity is a function of the density ratio of the projectile and target. However, it is also dependent on the impact velocity and porosity of the target.
  3. The normalized diameters of craters on porous targets tends to decrease with increasing target porosity. An empirical scaling law derived for porous sedimentary rocks based on conventional scaling laws is shown to be a reference for craters on brittle targets, including porous targets of various porosities.
  4. The depth-to-diameter ratio of the crater cavity is roughly 0.5 for tuff and gypsum, with porosities of about 43% and 50%, respectively. On the other hand, the ratio is about 0.2 for sandstones and cement mortar, although the porosity of cement mortar is about 40% and similar to that of tuff. No strong velocity dependence is evident in the depth-to-diameter ratio, although the ratio changes with impact velocity for microcraters produced on non-porous glass.
  5. Crater shape is roughly a trigonal pyramid for craters with a depth-to-diameter ratio of less than 0.3

References:

  1. Daubar, I. J., C. Atwood-Stone, S. Byrne, A. S. McEwen, and P. S. Russell (2014), The morphology of small fresh craters on Mars and the Moon, J. Geophys. Res. Planets, 119, 2620–2639, doi:10.1002/2014JE004671.
  2. Impact cratering on porous targets in the strength regime by Akiko M. Nakamura (PDF)
$\endgroup$
0
$\begingroup$

Pit crater
Credits: NASA/JPL-Caltech/University of Arizona

This image is a screenshot of the color version of HiRISE's ESP_043222_2035.
From Pit Crater near Elysium Mons:

This image was taken of an area on the lower southeastern flank of the volcano Elysium Mons. In the center is a small, dark pristine-appearing pit approximately 130 meters in diameter, which is clearly visible among the numerous small impact craters that are heavily covered by dust and sediment.

Garden variety craters are excavated by impacts and are characterized by raised rims, sloped walls and surrounded by ejecta blankets, but pit craters are simply sink holes in the ground with near vertical walls and floors that are only visible when the sun is high in the sky. They are deep holes that may lead to underground caves in volcanic terrain.

When the image was taken the Sun was about 51⁰ above the horizon, and we can see that the shadow of the crater rim then reached about the center of the floor.
So the depth of the crater floor center then is: tan 51⁰ x 65 m. = ~ 80 m., and the d/D ratio: ~ 0.6.

$\endgroup$

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.