In many news articles, it's mentioned that the MarCO spacecraft, launched with InSight, used fire extinguishant as the propellant for its cold gas thrusters. I originally assumed that this was referring to Halon, but it turns out that they actually used FE-36, a chemical designed to replace Halon in fire extinguishers. (I learned this here).

According to FE-36's MSDS PDF, its liquid density is 1.37 g/cm3, less than Halon 1301's 1.54 g/cm3 (though higher than nitrogen's .808). It does have a very high molar mass of 152.04 g/mol (compare to nitrogen's 14.01 g/mol), but I'd expect this to be bad for thruster applications due to a lower exhaust velocity.

So, why pick FE-36? Why not Halon, or just nitrogen or CO2?

  • $\begingroup$ Liquid nitrogen has a temperature of 77 K or -196 °C, but FE-36, Halon or CO2 could be liquid at room temperature under sufficient pressure. For space probes a storable propellant is needed, liquid nitrogen would evaporate too fast. $\endgroup$
    – Uwe
    Commented Dec 9, 2018 at 23:11
  • $\begingroup$ Thanks, that's a good point @Uwe. (related). I don't know MarCO's intended operating temperature range, though; would it need to be at room temperature during operation? Or just during handling and launch? $\endgroup$ Commented Dec 9, 2018 at 23:27
  • $\begingroup$ It is also considered a 'green propellant' since its inhalation toxicity is very low, making handling on the ground significantly easier vs traditional cold gas propellants. It is also widely available. Another nice feature is that it is not explosive, so it is safer, i.e. less risk to the primary payload $\endgroup$ Commented Dec 12, 2018 at 5:17
  • 1
    $\begingroup$ I've added a bounty here. Note that there will be some synergy with What are some notable cold gas thruster propellants, and why?, and it's always okay to post an answer to your own question. $\endgroup$
    – uhoh
    Commented Dec 16, 2018 at 3:18

1 Answer 1


Short explanation

The company that built the drive seems to have settled on FE-36 as the default propellant for many of their propulsion systems, in part due to limitations of launching it from the ISS.

Long explanation

propulsion block

MarCO is using a propulsion system built by VACCO. Most of their public information about this specific block is here and here, but that does not contain a lot of information. However their cubesat propulsion system overview page states:

The cold gas propulsion systems are coveted for their low cost propellant, ease of installation and simplicity of use. This low risk approach was chosen for the first interplanetary CubeSat propulsion module.

On the same page is this table [red box added]


It shows that R236FA (which is another name for FE-36) is used by many of their propulsion systems

From the CubeSat High Impulse Propulsion System (CHIPS) Design and Performance paper:

The CHIPS baseline propellant is R236fa: a self-pressurizing, non-toxic and inert refrigerant in widespread commercial use. R134a is a good alternate propellant option because it has slightly higher total performance, but has higher tank pressure and cannot be scrubbed by filters in the International Space Station (ISS); for these latter reasons related to range safety and deployment, R236fa was selected as the baseline propellant.


The primary safety risk with CHIPS is pressure, but this is predominantly mitigated by the use of R236fa propellant rather than R134a. R236fa requires more preheating because of its lower vapor pressure, and its Isp performance is worse than R134a. However, with R236fa, the overall total impulse will be similar (Fig. 8) and more importantly, the propellant tank will be below 100 psig at the CHIPS maximum expected operating pressure (MEOP) under worst-case temperature conditions of 65°C, so it is not a hazardous pressure system [AFSPCMAN 91-710, Vol. 3 Chap. 12]. This is extremely low compared with pressures routinely encountered in the space industry and does not present a serious safety issue. As such, R236fa is now considered as the baseline propellant choice (R134a was the original baseline propellant).

That specific propulsion system is also built in collaboration with VACCO, but it is a resistojet. After using that fuel for their resistojets they probably spread it over their whole line for simplicity and became the "baseline propellant of choice" for VACCO. That is why it is also used by VACCO for MarCO, even though the ISS is not a limiting factor for it. It most likely uses a lot of the internal technology of other propulsion systems built by them.

  • 1
    $\begingroup$ But it builds upon technology built by the company in the past which had to deal with those constraints $\endgroup$
    – Hans
    Commented Dec 19, 2018 at 15:13
  • 1
    $\begingroup$ That is what the current last sentence is supposed to mean. But I am adding more explanation. $\endgroup$
    – Hans
    Commented Dec 19, 2018 at 15:16

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.